Is the energy produced by the hydro-electric power affected by external factors like the altitude or the climate?

Energy produced by hydroelectric power is affected by external factors such as altitude and climate. The generation of hydroelectric power depends on water, with comes from rainfall. When there is lesser rainfall or snowmelt in that area, the amount of energy produced by hydroelectric power will be lesser. When the climate is very hot, there will be less water as the water has evaporated due to the heat. Thus, there will be less water available to produce hydroelectric energy, and so there will be less energy.

By damming up areas at high altitudes, the water at the area behind the dam will have more gravitational potential energy than that of water that is dammed up at a lower altitude. With more gravitational potential energy, more energy would be produced by the hydroelectric power.

Different types of hydroelectric power used in different parts of the world

There are three types of hydroelectric installations used in the world:
• Storage
• Run-of-river
• Pumped-storage facilities.


Storage facilities use a dam to capture water in a reservoir. This stored water is released from the reservoir through turbines at the rate required to meet changing electricity needs or other needs such as flood control, fish passage, etc.

Drawing courtesy of U.S. Department of Energy

Run-of-river facilities use only the natural flow of the river to operate the turbine. If the conditions are right, it can be constructed without a dam or with a low diversion structure to direct water from the stream channel into a penstock.


(Image taken from: http://www.nwcouncil.org/Library/2004/2004-1/Wanapum_sm.jpg )This Run-of-River project is in Idaho Falls, Idaho. Run-of-River Projects– utilize the natural flow of the river.

(Image taken from http://www.switchinggears.com/images/tazimina_small.jpg )
This picture shows The Tazimina Project in Alaska which did not require a dam.
Use of Diversion Hydropower– Channels a portion of the river through a canal.

Pumped-storage facilities, an innovation of the 1950s, have specially designed turbines. These turbines have the ability to generate electricity the conventional way, that is, when water is delivered through penstocks to the turbines from a reservoir. However, they can also be reversed and used as pumps to lift water from the powerhouse back up into the reservoir where the water is stored for later use. During the daytime when electricity demand suddenly increases, the gates of the pumped-storage facility are opened and stored water is released from the reservoir to generate and quickly deliver electricity to meet the demand. At night when electricity demand is lowest and there is excess electricity available from coal or nuclear electricity generating facilities the turbines are reversed and pump water back into the reservoir. Operating in this manner, a pumped-storage facility improves the operating efficiency of all power plants within an electric system.

Drawing courtesy of U.S. Department of Energy

Hydroelectric power distribution

• Most imprtant and widely-used renewable source of energy
• Represent 19% of total electricity production
• Canada is the largest producer of hydroelectricity, followed by the United States, China, Russia and Brazil and they accounts for over 50% of the total hydroelectric generating capacity of the world.
• two-thirds of the economically feasible potential remains undeveloped in countries such as India and China
• In countries like Norway, Iceland, and Canada, hydroelectricity accounts for more than half of the total electricity supply of the country.

Good and Bad of Hydroelectric Power

Good points to note:

• Do not emit harmful asmospheric pollutant E.g. carbon dioxide
• Does not contribute to global warming/ acid rain
• Do not result in the risks of radioactive comtamination
• Regulate seasonal variation in water which prevents flooding
• Bom to local economy because these places would be good location for water sports and fishing (tourism)
• Water can still be used for irrigation and drinking even when after it travels through a dam

Bad points:

• Flood large areas of land that may be forested causing deaths of thousands of organisms
• Vegetation previously covering these lands would rot and give off carbon dioxide and other greenhouse gases
• These gases are equivalent to those from other sources of electricity
• Damming a river change the amount and the quality of water downstream, preventing fish from migrating upstream to spawn
• Silt would be trapped in a dam and deposit on the bed of the reservoir altering the quantity of water and affecting electrical generation
• River downstream deprived of silt and river flood plain would not be fertilize, causing farmers to turn to man-made fertilisers which would pollute that water and land
• Bacteria would be formed when vegetation decay and pses a health hazard to people who feed on the aquatic animals (bioaccumulation)
• Dependent on the climate to stay constant, therefore when the amount of water in reservoirs decreases, the dams would not function properly
• Forced resettling for people who are displaced by flooding
• Loss of land used to grow food
• Low oxygen level and slightly acidic conditions promote growth of bacteris that releases metals such as mercury which fish absorbs
• Alter the quality of water, e.g. increased or decreased dissolved oxygen, increases in total dissolved gases, modified nutrient levels, thermal modification andheavy metal levels.

Hi! We are back again!
This time we are here to share with you about dams!!

In short:

By the way, before we start, let us set you thinking!
Do you know what dams are?
What are dams for?

Well, dams, they are, structural barriers built to obstruct or control the flow of water in rivers and streams. They are designed to serve two broad functions. The first is the storage of water to compensate for fluctuations in river discharge (flow) or in demand for water and energy. The second is the increase of hydraulic head, or the difference in height between water levels in the lake created upstream of the dam and the downstream river.
By creating additional storage and head, dams can serve one or more purposes:
- Generating electricity
- Supplying water for agricultural, industrial, and household needs;
- Controlling the impact of floodwaters; and
- Enhancing river navigation.
They can be operated in a manner that simultaneously augments downstream water quality, enhances fish and wildlife habitat, and provides for a variety of recreational activities, such as fishing, boating, and swimming.

In detail:

How dam works?

A typical dam is a wall of solid material built across a river to block the flow of the river thus storing water in the lake that will form upstream of the dam as water continues to flow from the river upstream of the dam.
The main purpose of most dams is to create a permanent reservoir of water for use at a later time. The dam must be watertight so that water does not leak out of the dam and escape downstream. An essential part of a dam is therefore the "impermeable membrane", ie the watertight part of the dam that prevents water leaking out. As we shall see later, it is not necessary that the entire dam wall be watertight. The natural earth or rock on which the dam is built (ie the dam foundation) must also be watertight, as must the river valley in which the storage reservoir forms. If these natural areas (dam foundation and storage area) are not watertight then water could leak out of the reservoir even if the dam itself is watertight.
As well as being watertight a dam must also be stable ie the dam wall must have sufficient strength to firstly, stand permanently under its own weight especially when at least part of the dam wall is saturated with water and secondly, resist the water pressure in the lake upstream of the dam. This water pressure exerts a force on the dam wall tending to push it downstream. The higher the dam, the greater the depth of water stored behind the dam and the greater the water pressure on the dam wall. The dam must also have sufficient strength to resist other forces to which it may be subjected from time to time eg shaking from earthquakes. The threat that earthquakes pose to dams varies widely depending on the region of the world in which the dam is located.
A dam must have some way of releasing water in controlled amounts as it is needed ie an outlet valve of some type. Depending on the purpose of the dam the water may be released into a pipeline to supply a city with water, or into a hydro-electric power station to generate electricity or the water may simply be released into the river bed downstream of the dam and allowed to flow naturally down the river, eventually to be pumped out and used for irrigation of crops further downstream. The outlet valve must be connected via a pipe or tunnel to some type of intake structure where the water is actually drawn from the storage reservoir.
When the river on which the dam has been built floods a very large volume of flood water will flow into the storage reservoir. Usually this is very, very much more water than can be released through the outlet valve. A dam must have some means whereby these large volumes of flood water can flow around the dam without causing damage to the dam itself; ie a spillway which, in most cases, is an open cut channel large enough to carry the flood water around the dam. If the dam is built of concrete the spillway may form part of the dam wall itself. However, if the dam is built of earth and/or rock fill (ie soil and broken rock) the spillway must be a separate structure because flood waters cannot be allowed to flow over the top of a fill (or embankment) dam which would be quickly washed away by the flood water if this was to happen.

A large dam project may involve many types of construction apart from building the dam wall itself eg tunnelling for diversion or outlet works; road building to replace roads flooded by the reservoir; quarrying to obtain rock fill and other construction materials; excavation of open cuts for the spillway, access roads and road deviations

There are mainly 4 major classes of dams are based on the type of construction and materials used: embankment, gravity, arch, and buttress.

1. Embankment.
Embankment dams typically are constructed of compacted earth, rock, or both, making them less expensive than others that are constructed of concrete. Consequently, more than 80 percent of all large dams are of this type. Embankment dams have a triangular-shaped profile and typically are used to retain water across broad rivers.
2. Gravity.
Gravity dams consist of thick, vertical walls of concrete built across relatively narrow river valleys with firm bedrock. Their weight alone is great enough to resist overturning or sliding tendencies due to horizontal loads imposed by the upstream water.
3. Arch.
Arch dams, also constructed of concrete, are designed to transfer these loads to adjacent rock formations. As a result, arch dams are limited to narrow canyons with strong rock walls that can resist the arch thrust at the foundation and sides of the dam.
4. Buttress.
Buttress dams are essentially hollow gravity dams constructed of steel-reinforced concrete or timber.

Do you know how dams are constructed?

Careful planning throughout the siting, design, and construction of dams is necessary for optimal utilization of rivers and for preventing catastrophic dam failure. These planning phases require input from engineers, geologists, hydrologists, ecologists, financiers, and a number of other professionals.
Designers must first evaluate alternative solutions and designs for meeting the same desired objective, whether the goal is to allocate water supply, improve flood control, or generate electricity. Each alternative requires a comprehensive cost-benefit analysis and feasibility study for evaluating its physical, economic, ecological, and social impact.
Once an alternative has been selected, a number of important considerations enter into the design and construction of the dam. These include:
- Hydrological evaluation of climate and streamflows;
- Geologic investigation for the foundation design;
- Assessment of the area to be inundated by the upstream lake (also called a reservoir) and its associated environmental and ecological impacts;
- Selection of materials and construction techniques;
- Designation of methods for diverting stream flow during construction of the dam;
- Evaluation of the potential for sediments to accumulate on the reservoir bottom and subsequently reduce storage capacity; and
- Analysis of dam safety and failure concerns.

When planning is all done, here comes the construction!

Construction work on a dam project is carried out at the dam site itself and also at other locations such as spillway site, rock fill quarry, clay and gravel borrow areas and road works which may be near the dam site or, in other cases, may be considerable distances from the dam site.From a construction point of view the dam site consists of the river bed area which is normally submerged by the river and the abutments or valley sides above the river bed. No work can be carried out in the river bed area until the river has been diverted, usually through a tunnel or channel. After diversion the river bed area is dry and construction of the dam wall can commence.
Before the dam wall can be built two important preliminary steps have to be completed: the dam foundation area must be stripped of overburden (ie material, usually soil, which is unsuitable for dam construction must be removed and disposed of), and the foundation for the dam must be prepared. Foundation preparation usually consists of two quite different activities: removal of pockets and seams of weak material and replacement of this material with "dental" concrete, so called because the work resembles filling cavities in teeth; the second aspect of foundation preparation is grouting. Grouting involves drilling holes (often to quite great depths, equal to the height of the dam in some cases) and then pumping these holes full of cement grout (a mixture of cement and water). The purpose of grouting is to fill up open cracks in the rock foundation on which the dam is to be built so that water will not leak out of the reservoir after the dam is finished.Once the foundation preparation is complete the construction of the dam wall itself can commence by hauling, dumping and compacting construction materials such as clay and rock fill. Compaction is carried out to ensure that the fill, as placed, will have the maximum possible density. Properly compacted fill will have the desirable engineering properties of high strength and low settlement over time, and, in the case of clay fill for a dam core, low permeability, which is important to reduce the likelihood of failure by piping or internal erosion.

A typical construction sequence for a fill dam is:

Stage 1: Excavate diversion tunnel and build coffer dams. The milestone of diverting the river through the diversion tunnel marks the end of this stage.

Stage 2: Strip dam foundation of overburden. Carry out foundation treatment and grouting. Excavate and haul fill construction materials from their sources and place and compact in the dam embankment. The end of this stage is marked by the milestone of closure of the diversion tunnel to start the storage of water in the dam reservoir. Excavation of the spillway will also be under way during this stage.

Stage 3: Complete outlet works, spillway and all other parts of dam project.
Management of floods during construction is one aspect always given considerable attention by the engineers designing the dam. Before the design of the dam can be completed engineering geologists have to find sources of suitable clay, gravel and rock which can be used as construction materials with which the dam wall can be built.

In fact, a dam project passes through four phases during its life;
- Investigation phase
- Design phase
- Construction phase
- Operation and Maintenance phase

When a dam is put into operation, or commissioned, water is released from the upstream reservoir over a spillway or through gates in a manner to satisfy intended objectives. Operating rules for maximizing power generation, for example, include maintaining hydraulic head. In contrast, water levels in flood control reservoirs must be periodically reduced to allow for new storage during anticipated periods of flood hazard. Operating issues, however, can easily become complex and highly politicized and may be difficult to resolve. This is particularly true for river systems containing several reservoirs, for dams serving multiple purposes, and in cases where adverse social, ecological, and environmental impacts are significant.

Do you know what dams are for?

Dams are usually built for one or more of the following reasons:

1) To provide a supply of water for towns, cities and mining sites; eg Warragamba Dam, Australia is the main water supply dam for the city of Sydney.

2) To contain and store waste (tailings) from mines; eg Omai Tailings Dam, Guyana, South America which stored waste from a gold mining operation.

3) To provide a supply of water for the irrigation of crops; eg Burrinjuck Dam, Australia which was built as the main head water storage for the Murrumbidgee Irrigation Area in New South Wales.

4) To generate electricity in hydro-electric power stations; eg Itaipu Dam, Brazil is the largest hydro-electric power station in the world.

5) To help control or mitigate floods; eg the Tennessee Valley Authority dams in the U.S.A. which help control floods on the Tennessee, the lower Ohio, and the lower Mississippi Rivers.

Many dams are multipurpose and most dams have at least some flood mitigation effect in addition to their primary purpose. Dams built specifically for flood control may have some of their storage capacity kept empty during normal river flow conditions so that space is available to store excess water inflow under flood conditions. The flood mitigation effect of a dam is such that the downstream river height at the peak of the flood is reduced but, after the peak has passed, the river levels usually remain high for a longer period than would have been the case if the dam had not been built. This is because excess flood water is only stored behind the dam temporarily and is slowly released from the dam in the days and weeks after the flood peak has passed.

Citations:

1) Linsley, Ray K. et al. Water Resources Engineering, 4th ed. New York: McGraw-Hill, 1992.
2) Mays, Larry W. Water Resources Engineering. New York: John Wiley & Sons, 2001.
3) Morris, Gregory L., and Jiahua Fan. Reservoir Sedimentation Handbook. New York:McGraw-Hill, 1998.

Hope that you have a clearer idea what dams are and what they are for!
So see you again soon!
Signing off!

Hydroelectricians:D

Here are the types of hydro turbines!

There are two main types of hydro turbines: impulse and reaction. The type of hydropower turbine selected for a project is based on the height of standing water—referred to as "head"—and the flow, or volume of water, at the site. Other deciding factors include how deep the turbine must be set, efficiency, and cost.

Impulse Turbine The impulse turbine generally uses the velocity of the water to move the runner and discharges to atmospheric pressure. The water stream hits each bucket on the runner. There is no suction on the down side of the turbine, and the water flows out the bottom of the turbine housing after hitting the runner. An impulse turbine is generally suitable for high head, low flow applications.
Pelton A pelton wheel has one or more free jets discharging water into an aerated space and impinging on the buckets of a runner. Draft tubes are not required for impulse turbine since the runner must be located above the maximum tailwater to permit operation at atmospheric pressure. A Turgo Wheel is a variation on the Pelton and is made exclusively by Gilkes in England. The Turgo runner is a cast wheel whose shape generally resembles a fan blade that is closed on the outer edges. The water stream is applied on one side, goes across the blades and exits on the other side.

A pelton turbine.
- Cross-Flow
A cross-flow turbine is drum-shaped and uses an elongated, rectangular-section nozzle directed against curved vanes on a cylindrically shaped runner. It resembles a "squirrel cage" blower. The cross-flow turbine allows the water to flow through the blades twice. The first pass is when the water flows from the outside of the blades to the inside; the second pass is from the inside back out. A guide vane at the entrance to the turbine directs the flow to a limited portion of the runner. The cross-flow was developed to accommodate larger water flows and lower heads than the Pelton.
- Reaction Turbine
A reaction turbine develops power from the combined action of pressure and moving water. The runner is placed directly in the water stream flowing over the blades rather than striking each individually. Reaction turbines are generally used for sites with lower head and higher flows than compared with the impulse turbines.
- Propeller
A propeller turbine generally has a runner with three to six blades in which the water contacts all of the blades constantly. Picture a boat propeller running in a pipe. Through the pipe, the pressure is constant; if it isn't, the runner would be out of balance. The pitch of the blades may be fixed or adjustable. The major components besides the runner are a scroll case, wicket gates, and a draft tube. There are several different types of propeller turbines: - Bulb turbine The turbine and generator are a sealed unit placed directly in the water stream.
- Straflo
The generator is attached directly to the perimeter of the turbine.
- Tube turbine
The penstock bends just before or after the runner, allowing a straight line connection to the generator.
- Kaplan
Both the blades and the wicket gates are adjustable, allowing for a wider range of operation.

A Kaplan turbine
- Francis
Francis turbine has a runner with fixed buckets (vanes), usually nine or more. Water is introduced just above the runner and all around it and then falls through, causing it to spin. Besides the runner, the other major components are the scroll case, wicket gates, and draft tube.
- Kinetic
Kinetic energy turbines, also called free-flow turbines, generate electricity from the kinetic energy present in flowing water rather than the potential energy from the head. The systems may operate in rivers, man-made channels, tidal waters, or ocean currents. Kinetic systems utilize the water stream's natural pathway. They do not require the diversion of water through manmade channels, riverbeds, or pipes, although they might have applications in such conduits. Kinetic systems do not require large civil works; however, they can use existing structures such as bridges, tailraces and channels. Hope that you have learnt more about the hydroelectric turbines!

Signing off,
Hydroelectricians!:D

How it works

Hello!
Now we are going to share with you HOW HYDROTURBINES WORK!


Water flows from a dam or reservoir through a valve called a penstock that regulates the flow. It then passes through a spiral-shaped pipe to make the water spin. The spinning water makes a turbine turn. The turbine then powers an electrical generator while the water is released downstream.
To make the generator work properly the turbine must spin at a constant speed. Using a speed governor to open and close water gates surrounding the turbine does this. This controls the speed and volume of water flowing to the turbine.
It is also possible to turn off the flow of water altogether using an enormous valve, so that maintenance can occur.
The amount of electricity that can be produced by hydroelectricity generation depends on two things: the rate at which the water flows and the head of water. This is the difference in height between the water in the dam or reservoir and the water below the turbine.



The theory is to build a dam on a large river that has a large drop in elevation. The dam stores lots of water behind it in the reservoir. Near the bottom of the dam wall there is the water intake. Gravity causes it to fall through the penstock inside the dam. At the end of the penstock, there is a turbine propeller, which is turned by the moving water. The shaft from the turbine goes up into the generator, which produces the power. Power lines are connected to the generator that carries electricity to your home and mine. The water continues past the propeller through the tailrace into the river past the dam. By the way, it is not a good idea to be playing in the water right below a dam when water is released!

Parts of a Hydroelectric Plant
Most conventional hydroelectric plants include four major components:
Dam. Raises the water level of the river to create falling water. Also controls the flow of water. The reservoir that is formed is, in effect, stored energy.
Turbine. The force of falling water pushing against the turbine's blades causes the turbine to spin. A water turbine is much like a windmill, except the energy is provided by falling water instead of wind. The turbine converts the kinetic energy of falling water into mechanical energy.
Generator. Connected to the turbine by shafts and possibly gears so when the turbine spins it causes the generator to spin also. Converts the mechanical energy from the turbine into electric energy. Generators in hydropower plants work just like the generators in other types of power plants.
Transmission lines. Conduct electricity from the hydropower plant to homes and business.

How Much Electricity Can a Hydroelectric Plant Make?
The amount of electricity a hydropower plant produces depends on two factors:
How Far the Water Falls. The farther the water falls, the more power it has. Generally, the distance that the water falls depends on the size of the dam. The higher the dam, the farther the water falls and the more power it has. Scientists would say that the power of falling water is "directly proportional" to the distance it falls. In other words, water falling twice as far has twice as much energy.
Amount of Water Falling. More water falling through the turbine will produce more power. The amount of water available depends on the amount of water flowing down the river. Bigger rivers have more flowing water and can produce more energy. Power is also "directly proportional" to river flow. A river with twice the amount of flowing water as another river can produce twice as much energy.As you should know, the main part of the hydro turbine is the most important part—the generator! But do you know how does the hydro turbine works?
Well, hydraulic turbine converts the energy of flowing water into mechanical energy. A hydroelectric generator converts this mechanical energy into electricity. The operation of a generator is based on the principles discovered by Faraday. He found that when a magnet is moved past a conductor, it causes electricity to flow. In a large generator, electromagnets are made by circulating direct current through loops of wire wound around stacks of magnetic steel laminations. These are called field poles, and are mounted on the perimeter of the rotor. The rotor is attached to the turbine shaft, and rotates at a fixed speed. When the rotor turns, it causes the field poles (the electromagnets) to move past the conductors mounted in the stator. This, in turn, causes electricity to flow and a voltage to develop at the generator output terminals.:D

In the next post, we will be going into the details of the turbines.

Signing off,
Hydroelectricians!:D

Converting Moving Water to Electricity

Hi! We are back!
This time we will be sharing more about the conversion of moving water to electricity!

In the hydroelectric dam, the water stored at a higher elevation is a source of potential energy. When released, it runs through a pipe called a penstock, and is delivered to the turbine. The potential energy is then converted to kinetic energy in the turbines and then to electrical energy. Generally more than 90% of the potential energy of the water can be converted into electrical energy, which means that the Power-Work efficiency is 90%.

In order to generate electricity from the kinetic energy in moving water, the water has to be moving with sufficient speed and volume to turn a generator, which explains why the water is stored at a higher elevation. One gallon of water per second falling one hundred feet can generate approximately one kilowatt of electrical power.

The key factors that maximise the amount of energy produce are the volume of water and the height difference between the intake and the outflow of water. This height difference is called the head. Thus to produce maximum power, it is best to locate the hydroelectric plant at the maximum elevation. The height difference is proportionate to the speed of the water and the water pressure in the penstock. Therefore, these factors can be placed aside.

The energy produced is determined by the mass of the water, the gravitional acceleration which is a constant and the height where the water is released. This is derived from the potential energy formula, E = mgh. Whereas the power is given by a function of rate of fluid flow or the head. This is because, power equals to energy produced over time, E/t = m/t(g)(h) and m/t is the rate of fluid flow. The rate of fluid flow is proportionate to the head. Therefore, to obtain maximum energy and power, there must be maximum height difference and volume of water.

Citations:

• Union of concerned scientists. (16/11/07). Clean energy. USA, retrieved 1/4/08, from http://www.ucsusa.org/clean_energy/renewable_energy_basics/how-hydroelectric-energy-works.html
• Barry Gilman. (2008). How it works: Hydropower. Southern California Edison, retrieved 13/4/08, from http://www.sce.com/Feature/Archive/hydropowerfeature.htm
• K.S.Sidhu. Hydropower. India,Punjab state electricity board, retrived 5/5/08, from http://www.indiacore.com/bulletin/papers-gp5/k-s-sidhu-hydro-power.pdf
  

Signing off,

Hydroelectricians:D

Brief Introduction on hydroelectric power.

Now let us start off with some basic research:
There are two main questions we would like to address first, which we will give a short introduction to. Further details will be provided at a later date.

THE IMPACTS OF HYDROELECTRICITY ON THE ENVIRONMENT?

Hydroelectric power is used to supply electricity to many parts of the world today, such as America, China and India. Hydropower provides up to one-fifth of the world's electrical energy, second to fossil fuels. At the same time, hydroelectric plants are long lasting. For example, the Grand Coulee dam has been in operation since 1942.

Building hydroelectric plants have its advantages and disadvantages as well.

• A dam could flood vast areas of land up stream, altering the natural ecosystems. The ecosystems along the banks of the river are usually diverse habitats originally, after the dam has been built, these habitats are replaced by a relatively uniform reservoir, which usually supports a much smaller range of animal species.
• Dams also modify the river flows by releasing water to produce energy, irrigation or even for navigation and recreation.
• Moreover, dams can lower the quality of the water. As the amount of water is reduced there is no longer enough water travelling downstream to rinse the ecosystem, it may increase the salinity of the water and alters the natural habitat as well.
• Dams block the access to certain species of migratory fish’s breeding or feeding sites. Fish ladder is a possible solution but it is not always effective, and is not a feasible solution for many tropical rivers.
• However, in places where natural water bodies are almost absent, dams provide the essential natural habitats for many birds.
• Some dam projects have implemented specific habitat restoration measures that can to a certain extent compensate for the negative impacts of dams.
• The main advantage of dams on the environment is that it is renewable and cheap. We only need to pay for building and maintaining the power stations and the dams.
• The whole process is also environmentally friendly, as it create minimal air, chemical, water or thermal pollution and almost does not contribute to global warming.
• Furthermore, the use of hydroelectric power solves the problem caused by the fast depleting coal, oil and other non-renewable fuel.

WHAT ARE SOMES OF THE ADVANTAGES OF HYDRO-ENERGY?

Hydroelectric energy offers a number of advantages for people who use it, the environment.

• Cost of fuels are constantly rising therefore using hydroelectric power can help save a lot of money, by making electricity costs lower and more stable.
• Minimal pollution caused to the environment as it does not produce radioactive waste accepts for when the power stations are initially built. However, all power plants pollute the environment when they are first built. Less greenhouse gases are produced as compared to burning of fossil fuels.
• Cut down on number of employees as these plants are largely automated thus cutting down on costs
• Can be set up in any size, depending on the river or stream used to operate them
• Renewable form of energy;it does not rely upon finite resources like natural gas or coal to generate power.
• Operate for many years after they are built compared to nuclear power plants which generally lasts for 30-40 years
• Small hydro electricity generation systems sometimes offer more economic advantages for home owners than solar power, and tend to last longer than solar panels do.

Source Citation: Perry, Z. (2007). Hydroelectric Power. HubPages, Retrieved Feb 25, 2008, from http://hubpages.com/hub/advantages-hydroelectric-power

That's all for now. Do come back often to check up on latest updates!

Yours Sincerely,

Hydroelectricians. :D

Dear bloggers,

WELCOME TO OUR PHYSICS BLOG!!

We are a group of students from Nanyang Girls' High School,Singapore, currently embarking on a research project on hydroelectrical energy. This is where we will be assessing, analyzing and displaying the results and research we have collected.

Rationale of our project:
1) study and identify the physics behind hydro-electric power:
i) Energy conversion involved in the production of the hydro-electric power
a)The best and most suitable conditions needed i.e. the pressure of the water, height which
the water falls, the speed of the water to attain the highest energy.
b)How the turbine converts the energy
c)How are the dams and the turbines constructed
d)Different types of hydroelectric power used in different parts of the world
e)Is the energy produced by the hydro-electric power affected by external factors like the
altitude or the climate
2)To study how the hydro-electric power saves the earth:
a)impacts of the hydro-electric power
b)how it benefits the environment;
c)in contrast, in what way will it harm the earth
d)how and where it hydro-electric power used in other countries
is Singapore suitable to use hydro-electric power to do our part in saving the earth
e)how can we modify the hydro-electric energy system to make sure that it has the highest
efficiency i.e. can convert the most power, and at the same time have the minimal impact
on the earth.

Rationale of creating a Physics Blog:
1) that's part of the marking scheme
2) More importantly, it is to inform more people, not only Singaporeans, all the people in the world about Hydroelectric power:
i) its advantages
ii) its uses
iii) how it hydroelectric power contributes to the creation of a more eco-friendly earth.

Therefore, do not hesitate to spread to your loved ones about this blog, and share the information on hydroelectric power.

Disclaimer:
The contents of this site are purely the results of our physics research project. We will try to ensure the reliability of the contents, however we give no warranty for the accuracy of the information posted on this site. We hope that users acknowledge that we shall not be held responsible for all consequences that may be incurred by the user as a result of using the information on this site.

Please feel free to browse through our blog. Comments are welcomed.

your sincerely,

Hydroelectricians. :D